View All Network Setting. The “ifconfig” command with no arguments will display all the active …
# ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 nge0: flags=1000843 mtu 1500 index 2 inet 192.168.0.1 netmask ffffff00 broadcast 10.14.8.255 ether 0:14:4f:7d:20:9c ・ここで ifconfig -a plumb を入力 # ifconfig -a plumb ifconfig: SIOCSLIFNAME for ip: nge0: already exists ・ネットワークI/F 名の This command replaces the ifconfig command that is used in Oracle Solaris 10. dladm: Manages datalink configuration. This command replaces the ndd command and the drive.conf file that are used in Oracle Solaris 10 for configuration of certain network parameters. route: Configures persistent routes. This command replaces the /etc/defaultrouter Bringing up an interface using ifconfig is pretty straight-forward. The big drawback is that the interface configuration will not persist across a reboot: bleonard@solaris:~$ sudo ifconfig e1000g0 plumb 10.0.2.15/24 up New School. The new ipadm command is a little more esoteric, however, its settings do persist across a reboot: I read the man page for netmasks and ifconfig but didn't find info about default netmask or network classes in them. Am I looking at the wrong man pages? It looks like zonecfg is maybe relevant, I will check that. – hilcharge Mar 4 '16 at 10:00 How to configure Solaris 10 Probe based IPMP How to configure Solaris 10 Link Based IPMP Solaris IP multipathing provides the high availability and load balancing capability to the networking stack. It makes sure to avoid any single point of failure on network side. I am very new to Solaris, after I install solaris-10, I can't find my internet interface. I tried ifconfig -a and it return nothing. I tried prtconf -pv I found my ethernet controller: vendor-id: 000010ec device-id: 00008139 name: 'pci5853,1' I tried ifconfig rtl0 plumb got the following error: The script will evaluate things like: if the OS is Solaris 10 then, show the nic available and ip that it use, in case that the OS will be a Solaris 11 then, show [other part.] I hope to be very clear explaining this. I used ifconfig command instead ipadm because I have Solaris 10 and Solaris 11 systems actually.
Feature Article: GRUB and the Solaris 10 1/06 OS: The New
Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. | The UNIX and Linux Forums The next procedure contains applies to users of the Solaris 10 3/05 OS only. If you are using an update to Oracle Solaris 10, refer to How to Remove a Physical Interface . On the system with the interface to be removed, assume the Primary Administrator role, or become superuser. The following ifconfig command does update the IP address together with both correct netmask & broadcast but don't believe that this change will stay after reboot: #ifconfig bge0 inet 203.20.160.91 netmask 255.255.255.0 broadcast 192.168.1.255 The value in /etc/netmasks (softlinked to /etc/inet/netmasks) is: 10.56.120.0 255.255.252.0 The value Jun 03, 2020 · #ifconfig -a lo0: flags=2001000849
Hello, Iam having problems getting more then one ip to work here is my setup! Hostname: nexus NIC: e000g1 (example ips) My ips 80.80.80.15 to 80.80.80.20 Defaultrouter 80.80.80.1 nameservers 80.80.80. | The UNIX and Linux Forums
Sun Solaris Servers Network Configuration Guide (SPARC Platform Only) To bind an IP address to a Network Interface Card #ifconfig -a --- to check the configuration #ifconfig qfe0 plumb --- to enable the first Network Interface Card #ifconfig qfe0